null
  Loading... Please wait...
Solar Panel Kits and Products

Solaris Blog - Square D Disconnect

How to Properly Size a Disconnect Box

Posted by


SquareD Disconnect

In terms of safety, properly sizing and utilizing a disconnect box is among is extremely important to ensure the lifetime of your system. Disconnect boxes are available for both AC and DC connections and can protect your inverter and utility components. Typically, there are two disconnect boxes in any given system, one for the DC connection and one for the AC connection. The DC connection is wired between the source of energy, in this case the solar panels, and your inverter. The DC disconnect is used to interrupt the DC current from the solar panels to the inverter in the event of a power surge. While the AC disconnect is used to separate the inverter from the electrical grid. The DC disconnect is typically installed in an indoor environment, while the AC disconnect is installed in the outdoor environment, close to the electric meter. Both are equally important and are essential components to have for solar permits to be approved under the NEC requirements.

In general, in order to size an AC or DC disconnect you must consider the voltage, circuit load, amps or breaker size and wiring of your equipment, components and connectivity throughout your solar array. According to NEC 690.10 “The circuit conductors between the inverter output and the building or structure disconnecting means shall be sized based on the output rating of the inverter. These conductors shall be protected form over currents in accordance with Article 240. The over current protection shall be located at the output of the inverter.” Perfectly clear? Not so much? Let’s break it down.

Standard Array Sizing Specifications

Maximum System Voltage:
  • 600 VDC
Range of Operating DC Voltage:
  • 200-600 VDC
Maximum Operating Current (DC):
  • 9.5 Amps
Maximum Array Short Circuit Current (DC):
  • 10 Amps
Maximum Utility Back Feed Current (DC):
  • 0.075 Amps
Operating Voltage Range (AC):
  • 106-132 VAC
Operating Frequency Range:
  • 59.3-60.5 Hz
Nominal Output Voltage (AC):
  • 120 VAC
Nominal Output Frequency:
  • 60 Hz
Maximum Continuous Output Current:
  • 15.0 Amps
Power Factor:
  • >0.99
Maximum Continuous Output Power (AC):
  • 1800 Watts
Maximum Output Fault Current (AC):
  • 15 Amps
Maximum Output Over-Current Protection:
  • 15 Amps
Efficiency:
  • 96.5%
Total Harmonic Distortion:
  • <5%


Taking standard measurements, lets us say we have a PV array which consists of 20 parallel-connected PV-strings. Each string has 30 series connected solar panels, and each of those panels has a maximum Voc of 28.4 VDC an Isc of 7.95 Amps. The highest inverter power output is calculated at the maximum power point, which occurs at approximately 146 A (IMPP).

The Voc determines the maximum voltage rating of the disconnect switch:

30 x 28.4 V = 852 Volts

Selecting a disconnect switch with a VI and VE of 1000 VDC would give a safety margin greater than 15%

The sum of ISC parallel-connected strings determines the current-capability requirements for the switch. Therefore, the sum of ISC:

20 x 7.92 A = 158 Amps

At a minimum, the NEC requires this value to increase by 125% to address increased current at peak sun hours.

If the ambient temperature is up to 60°C, temperature must be taken into account, for 60°C the factor is 0.80. Applying the factor by dividing the maximum power point current by the factor will show how the disconnect switch should be rated under normal conditions:

146 A / 0.80= 182.5 Amps

To find out more about sizing a disconnect switch, check out this article from Home Power - Solar Electricity Basics

To look at our available disconnect switches, we recommend starting with Square D.


View Comments




 

About Us

Solaris is a leading online solar energy supply store. Since our inception, we have steadily grown to become one of the most robust solar energy dealers nationwide. We provide a large variety of products, custom designed solar electric systems, and superb technical support throughout your installation.

Solaris-shop.com designs, supplies, and delivers complete solar energy systems for homeowners, and installers. We use only the highest rated manufacturers in our design layouts, customized for your specific needs and requirements. We have a commitment to excellence for our valued customers, offering wholesale pricing that ensures a powerful return on your investment, for years to come.

Solaris Blog

 

Share the Solar

newsletter


Solaris-Shop.com All Rights Reserved. 1501 W Tufts Ave Suite 208 Englewood, CO 80110 720-474-6050

Contact Us Today. Mon-Fri 7:00am - 4:00pm PST | Toll Free: 1-800-215-5350 | Local: 720-474-6050 | Email: customerservice@solaris-shop.com | Sitemap | Terms and Conditions | Copyright © 2024